Deep standing water in a cellar
Water over the floor drain level needs submersible pumps and a long discharge line. The speed is limited by the ground outside, not by the pump, and the crew decides the pace and watches for a rebound.
Standing water is pumped and extracted from a basement, floor or crawl space so that removal and drying can begin.
Fastest: call (833) 490-5225. Or send this and we call you back.
Manchester Water Damage Restoration extracts and pumps standing water for Manchester and Hillsborough County; phones are answered around the clock and a crew is dispatched as fast as one is available. Pumps and extractors take water off floors and out of low spaces before materials are removed and the structure is dried.
Every water loss that leaves a pool behind starts the same way. Before anyone can dry a wall or decide what to throw away, the water on the floor has to come out. That sounds simple until you stand in a cellar with a foot of water in it, a furnace in one corner and a stairway as the only way out.
Extraction is the first stage of drying, not a separate repair. Water left on a floor wicks upward into walls and soaks into subfloors, and every hour it stays there widens the area that needs drying. Taking it out fast, and in the right order, limits what has to be removed later and shortens the drying that follows.
Manchester Water Damage Restoration supplies the pumps, the extraction equipment and the people to run them. This page is about that stage alone: how water is moved out of a building, what limits how fast it can go, and why the pace is sometimes slower than people want. The cleanup and drying that follow are covered on other pages.
Do not enter standing water if the electrical panel, outlets or any appliance is wet, and do not pump a deep, flooded cellar against saturated ground without guidance. Water of unknown source should be treated as contaminated.
Water over the floor drain level needs submersible pumps and a long discharge line. The speed is limited by the ground outside, not by the pump, and the crew decides the pace and watches for a rebound.
A thin layer across a big open floor, such as a commercial or mill space, is not pumpable in the usual sense. Extractors and squeegees do the work. The area drives the time more than the depth.
A carpet can hold gallons of water that no pump will reach. Truck-mounted extractors lift it before the carpet is judged for removal. If the water was clean and the carpet is recent it can sometimes be saved.
Sewage or river water has to be pumped to a place where it can be discharged safely. Where it goes depends on the source, and the crew will not drain it into a yard or a storm drain without thought.
Call any hour and explain what is going on. You get a clear price before any work starts.
If the ground outside is still saturated, the water pressing on a foundation wall helps hold it in place. Emptying a cellar too fast can crack or shift the wall or lift the slab. Crews lower the water in steps and watch for a rebound.
A flooded cellar is held together, in part, by the water on both sides of the wall. Taking the inside water out suddenly removes that balance, and soil outside can push the wall in. The usual practice is to drop the level a little, wait, and check.
That is why people sometimes see a pump running and the water barely moving. A slow pace in the first hours is a precaution, not a lack of effort.
It goes where it cannot come back into the building, such as a yard that slopes away or a drain approved for the purpose. Contaminated water needs more care. A crew will not dump water where it harms a neighbor or recirculates to your foundation.
A discharge hose that empties beside the house defeats the work, because the water simply returns through the same crack. The hose is run to a point away from the foundation, and the outlet is checked during the job.
Sewage and river water are handled differently from clean water. The page on sewer backup cleanup and the one on Merrimack River flood water explain how that changes the work.
Submersible pumps move deeper water, wet vacuums and extractors handle shallow water and wet carpet, and generators supply power when the building's supply is off. The kit changes as the depth falls: pumps first, then extractors, then drying equipment.
Depth sets the tool. Inches of water need a pump and a long hose; a film needs an extractor. The crew often uses both at one site as the level falls.
Electric equipment in water is a hazard, so the crew checks the supply and uses suitable cords and protection. If the building's power must stay off, a generator is placed outside.
Stay out of standing water if power is on, turn off the water supply if a pipe is the source, lift small items off the floor, and photograph the water level. Do not start pumping a deep cellar against saturated ground. Call and describe what you see.
Photographs of the water at its highest point show the insurer how deep it was. A line on the wall in pencil is a quick way to mark the level.
If water is coming from outside, the source is not stopped by a pump alone. The crew will tell you what to watch for while they are on the way.
The crew checks how deep the water is, where it is coming from, and what electrical or gas equipment is near it. If the source is still running, it is stopped first.
Submersible pumps clear deeper water. Truck-mounted or portable extractors lift the thin film on carpet and hard floors. Hoses carry the discharge away from the foundation, to a place the water will not return.
When the ground outside is saturated, water inside a cellar is lowered gradually so the walls and slab are not stressed. The crew watches the level for a rebound, since a level that rises again points to a source still feeding it.
Once the standing water is gone, extractors pull water out of carpet and pad, and from low areas where it collects. This is the stage that reduces the load on the dehumidifiers.
Readings are taken to show what is still wet. Removal of the porous materials and the drying plan follow. Extraction is done when there is no standing water and no feed to the space.
Manchester's cellars are mostly the old kind, in a city where about 29 percent of homes were built in 1939 or earlier and ZIP summaries put most homes in 03102, 03103 and 03104 before 1940. Foundation walls of that age are not the poured walls of a recent house, and the crew is more cautious about lowering water against them. What the walls are made of in a given house is settled on the visit.
Water has more than one route into the city's buildings. The Merrimack and Piscataquog are the big rivers, and about 70 percent of the sewer system is combined, with overflows discharging to the rivers and to Ray Brook and Tannery Brook. That is a water-quality fact, and it is why extraction here starts with a question about what kind of water it is.
Downtown, the Amoskeag Millyard has large masonry buildings with big floors and deep basements. Extraction there is a matter of area and volume, and of finding a place to discharge a lot of water. The crew scopes the discharge route before starting, and does not assume a drain can take it.
Not sure if you're covered? Check your ZIP code.
River water that entered a home or building is removed, the contaminated materials taken out, and the structure dried and checked.
Rain, thaw and a high water table push groundwater into Manchester cellars. Standing water comes out first, then the structure is dried.
After the water is out, the building still holds it. Equipment and daily readings take wet framing, plaster and masonry down to dry.
Get everyone out of the water, keep away from anything electrical that is wet, and treat all river water as contaminated.
It depends on the depth, the area, the source and how fast the ground outside is draining. The crew will not give a number before seeing the space. A level that rebounds after pumping points to a source still feeding the water.
For a small, clean spill, yes. For a deep cellar, a power hazard or contaminated water, no. The risk is in the electrical supply and in the wall pressure, and the drying that must follow also needs equipment.
No. Extraction takes out the standing water. Drying removes the moisture held in walls, floors and framing. The page on structural drying and dehumidification explains the second stage.
Sometimes, if the water was clean and the carpet is extracted quickly. Carpet that took contaminated water is removed. The crew decides after extraction, with readings.
Then a source is still feeding it, such as groundwater, a pipe or a backed-up line. The crew will look for it, and a plumber or a drainage contractor may be needed to stop it.
Yes. The page on basement flooding after heavy rain describes how that loss is handled once the water is out.