Phones answered 24/7Manchester, NH
Call (833) 490-5225
(833) 490-5225
Serving Hillsborough County

Structural drying and dehumidification in Manchester

After the water is out, the building still holds it. Equipment and daily readings take wet framing, plaster and masonry down to dry.

  • Answered 24/7
  • Frozen pipes and ice dams
  • Merrimack flood cleanup

Get a fast quote

Fastest: call (833) 490-5225. Or send this and we call you back.

Structural Drying

Structural Drying and Dehumidification: what it covers

Quick answer

Structural drying removes the moisture that stays in framing, subfloors, plaster and masonry after standing water is gone, using air movers, dehumidifiers and daily meter readings. Manchester Water Damage Restoration answers calls for Manchester and Hillsborough County around the clock, and a crew is dispatched as fast as one is available.

Structural Drying and Dehumidification illustration for Manchester, NH

Pumping out the water is the part everyone sees. Drying is the part that decides whether the building recovers. Wood, plaster, brick and concrete are all porous to some degree, and after a loss they hold water that does not run or drip. It sits inside the material and leaves slowly, and if it stays long enough it brings mold, warped floors, loosened finishes and rot. Structural drying is the controlled process of getting that water out to a measured standard rather than by guesswork.

The method is not complicated, but it is exacting. Air movers sweep dry air across wet surfaces so that moisture leaves the material. Dehumidifiers pull that moisture out of the air so that it cannot settle somewhere else. The crew measures the material itself with meters, sets a dry reference from an unaffected part of the building, and returns on a schedule to read the same points again. Equipment comes off only when the readings arrive.

The part that is particular to Manchester is the building stock. A city with brick tenement blocks from the 1840s, a mill district on the Merrimack and a very large share of houses built before 1940 is a city of lath-and-plaster walls, thick masonry, balloon framing and old wood floors. These dry on their own timetable, and a drying plan written for a new drywall house will fail in them. The crew plans for the building in front of it.

Service area
Manchester & Hillsborough County
Availability
Phones answered 24/7
Warning signs

Signs you need structural drying and dehumidification

Do not run space heaters or portable fans in a wet room, and do not use a household vacuum on wet floors. Keep electrical cords off wet surfaces. If a ceiling is bowed or dripping, stay out from under it.

  • Walls that feel cool or damp days after the visible water is gone
  • Hardwood floors that cup, crown or lift at the edges
  • Windows that fog or run with condensation in a room that was wet
  • A musty smell that persists after cleanup
  • Plaster that stains, crumbles or loses its paint where it was wet
  • Baseboards, trim or door casings that swell and pull from the wall
  • A moisture meter or humidity reading that stays high in one room
  • Cold spots on a thermal image that do not fade between visits
Options

Types and options for structural drying and dehumidification

Conventional drying of framed rooms

Drywall, wood framing and standard flooring dry in a few days when the water is clean and the work begins promptly. Air movers and a dehumidifier do most of it, and drywall that has been wet for long enough is cut out rather than dried.

Drying plaster, lath and masonry

Old plaster over wood lath and brick or stone walls hold water far longer. The plan relies on slow, steady dehumidification, often with desiccant machines in cold conditions, and on long monitoring. Rushing it with heat can crack plaster and drive moisture deeper.

Drying under floors and in cavities

Water gets under hardwood, behind baseboards and into joist bays. Special mats or ports can pull air through these hidden spaces. The decision to save or replace a floor comes from the readings, not from its appearance.

One call and it gets handled.

A crew is dispatched as fast as one is available, and you approve the estimate before any work starts.

How long does structural drying take?

Most framed rooms take a few days, while plaster, brick and old wood floors may take longer. The time depends on the material, the amount of water, the temperature and humidity and how quickly the work began. The crew gives an estimate after the first readings and revises it.

There is no honest fixed number, and a promise of one should make you wary. The same volume of water behaves differently in a modern drywall room and in a masonry cellar. A heated, ventilated room dries faster than a cold, closed one, and a sudden cold spell can slow a job that was on schedule the day before.

What the crew can give you is a method: readings on day one, a dry reference, and a visit every day or two to check that the numbers are heading down. If they stall, equipment is moved or changed. The finish line is a measurement, and the work is finished when the measurement says so.

Why do old Manchester buildings dry differently?

Lath-and-plaster walls, brick and stone, balloon framing and thick old floors hold more water and release it more slowly than modern drywall construction. They also contain voids that let water travel. Drying them takes longer and needs more monitoring.

The Amoskeag worker districts, which date mostly from 1838 to 1882, are brick tenement blocks and overseer houses, and the houses of the surrounding neighborhoods include many built before 1940. Walls of that age are often plaster on wood lath over brick, or on studs without fire-blocking, which means a wet wall can be wet from the cellar to the attic. Water that gets into a bay can travel down inside it and show up two floors below the source.

A masonry wall is a heat sink and a moisture reservoir. Brick takes up water and holds it, and a cold wall cannot lose it quickly to cold air. In a New Hampshire winter the air outside has almost no moisture to take, so drying is done by dehumidifiers inside the building rather than by opening windows. Many cellars and mill buildings in the city have little heat, which pushes the plan toward desiccant dehumidifiers that work in cold conditions.

Can you dry in winter, when the heat is off and the air is cold?

Yes, but the plan changes. Cold slows evaporation, so crews use dehumidifiers designed for low temperatures, add controlled heat where safe and avoid opening windows. A frozen or unheated building is dried more slowly, and a frozen building has to be thawed carefully first.

Cold air holds little moisture, which is why a winter cellar feels damp but never seems to dry. Evaporation slows, the dehumidifier's coils frost over, and moisture can condense on the coldest walls. A desiccant machine works well in these conditions because it does not depend on cold coils, and a small amount of added heat can raise the rate of drying without baking the plaster.

In a building where pipes have burst in a cold snap, the first job is to find and stop the water, then thaw and dry. That sequence is covered in burst frozen pipe water damage. Where the water came from a roof, ice dam water damage explains the insulation and ceiling issues that follow.

How do you know the building is dry?

The material is dry when its readings match a dry reference from the same building and stay there on repeat visits. Surface feel and appearance are not enough. The crew records readings at fixed points and removes the equipment only when they match.

A wall can feel dry and still hold water, particularly masonry and plaster. Meters read the moisture content directly, and for materials that meters read poorly, such as thick brick, the crew compares like with like against an unaffected wall. Readings that rebound when the equipment is switched off mean the material was not dry.

Recorded readings are not only for the crew. They protect you if mold shows up later and if an insurer asks what was done. Keep the log, and ask for a copy at the end of the job.

Our process

How our structural drying and dehumidification visit works

  1. Map the wet area

    Moisture meters and a thermal camera show where water went, including into wall cavities and under floors. Readings are logged on a floor plan so that the boundary of the wet zone is known and can be checked again.

  2. Set the dry standard

    The crew takes readings from an unaffected part of the same building, in the same material. That sets the goal. A plaster wall in a 1900s house is compared with a dry plaster wall in that house, not with a number from a textbook.

  3. Place equipment to suit the building

    Air movers are placed to sweep the wet surfaces, dehumidifiers are matched to the volume and the humidity, and the space is closed off where it helps. In a masonry cellar or a tall plaster room the layout is different from a bedroom with drywall.

  4. Open what must be opened

    Drying through a surface works for some materials and not for others. Where water is trapped behind cabinets, under tile, in an insulated wall or behind a plaster ceiling, small openings, holes or panels are made so that air can reach it. Each opening is explained first and kept as small as possible.

  5. Monitor and remove equipment

    The crew returns, repeats the readings at the same points and adjusts the equipment. When material readings match the dry reference and the air is stable, the equipment is removed and the log is kept for your records and any insurance file.

Hillsborough County

Why structural drying and dehumidification is different in Merrimack Valley

Manchester's age shows in its construction. Roughly 29 percent of the city's housing was built in 1939 or earlier and another 25 percent between 1940 and 1969, according to a secondary summary of American Community Survey data. Some zip-code summaries say most homes in 03102, 03103 and 03104 predate 1940. The point for drying is that a large share of the city's housing is old enough to have plaster, solid framing or masonry foundations, and the crew expects it.

The mill district on the Merrimack adds large buildings with heavy timber, brick walls and big open volumes. Drying them is a matter of scale, and it connects to mill and multi-family water damage, where whole stacks of units can be affected through shared walls and floors.

After the May 2006 flood, when the Merrimack ran roughly 10 feet over flood stage in Manchester, buildings that took in river water needed long dry-outs. Floodwater is a different category from a clean leak, and sewage-contaminated or river-borne water brings the removal and cleaning steps described in sewer backup cleanup. Drying follows cleaning, never the other way round.

Related

Basement Flooding After Heavy Rain

Rain, thaw and a high water table push groundwater into Manchester cellars. Standing water comes out first, then the structure is dried.

Mold After Water Damage

Mold follows moisture. The fix is to dry the building, contain and remove growth on porous material, and clean what can be cleaned.

Ceiling and Drywall Water Damage

A stained, sagging or bulging ceiling means water is trapped above it. The board is opened, the source found, and the cavity dried before it is closed.

Mill-Era Multi-Family Water Damage

When one unit leaks, others get wet. Brick blocks and shared walls call for a plan that covers every unit, owner and floor involved.

Guides

Read before you book

FAQ

Structural Drying and Dehumidification FAQs

Why are the machines so loud?

Air movers and dehumidifiers run continuously to keep air moving and moisture leaving, and that is the cost of drying quickly. The noise is temporary. Turning them off early is the most common reason a building dries unevenly.

Will the equipment raise my electric bill?

Yes, for the days it runs. The crew will tell you how many machines are in use. If you are filing an insurance claim, ask your insurer how that cost is handled.

Can I just open the windows?

Only in warm, dry weather. In a New Hampshire winter or a humid summer day, outside air can add moisture. A closed space with dehumidifiers is usually faster.

Do you replace what cannot be saved?

The crew removes wet material that cannot be dried and documents it. Rebuilding is a separate contracting job, and you can choose who does it.

Is a state license required for this work?

New Hampshire does not issue a statewide license for water damage restoration, and we do not claim one. Plumbers and electricians are licensed through the Office of Professional Licensure and Certification, and asbestos work through the Department of Environmental Services.

What if the building has old paint or insulation?

Older buildings may contain lead paint or asbestos-containing materials. Disturbing them is regulated, with the Department of Health and Human Services handling lead and the Department of Environmental Services handling asbestos. The crew will pause and tell you before cutting into suspect material.

WhatsApp