Phones answered 24/7Manchester, NH
Call (833) 490-5225
(833) 490-5225
Guide

Drying Wet Walls and Floors in Old Manchester Buildings

How plaster, brick and old wood floors dry after water damage in older Manchester buildings, and why drying them takes measurement and patience.

Illustration for the guide "Drying Wet Walls and Floors in Old Manchester Buildings" (Manchester, NH)
Short answer

Plaster over lath, solid brick and old wood floors dry more slowly than modern drywall, and they hide moisture below the surface. Drying them means removing the standing water, controlling air and humidity, and checking readings daily until every material reaches its dry standard before anything is closed.

Key takeaways

  • Lath-and-plaster walls, thick brick and old floor boards hold water differently from modern drywall, so the same wet event takes longer to dry in an older building.
  • A surface that feels dry is not evidence of a dry wall, and moisture meters, thermal images and daily readings are how the crew knows.
  • Drying works by moving water out as vapour into air that is then dehumidified, not by heating the room or opening every window.
  • Manchester's Amoskeag-era brick blocks, with solid masonry and several households per building, need staged drying that treats each unit and the shared walls separately.
  • Cutting out wet material is sometimes right and sometimes unnecessary, and the decision should rest on readings and condition, not habit.
  • Old buildings may contain lead paint or asbestos-bearing materials, so testing before demolition is a step to ask about.

Why do old walls and floors dry differently from modern ones?

Older materials are thicker, denser and layered. Plaster sits on wood lath, brick is solid, and floors are made of wide boards over deep joists. Water moves into them slowly and leaves slowly too.

A modern wall is a sheet of drywall on studs, and when it gets wet the paper face takes up the water quickly, shows it plainly and can be cut out and replaced. A wall in an older Manchester house is built differently. A coat of plaster, often several, is keyed into wood lath nailed across the studs, with a gap behind. Water can travel behind the plaster, wet the lath and the studs and sit in the cavity, while the painted face looks nearly normal.

Brick and wood add to this. A solid brick wall, as in the Amoskeag districts, stores a great deal of water in its thickness and releases it from the surface over weeks rather than days. Old floors are usually softwood boards on joists that have seasoned for a century. They absorb and release moisture readily, and they cup and gap as they do. None of this means older buildings cannot be dried. It means the work depends on understanding each material and checking it, instead of treating every wall as drywall.

How does drying actually work?

Drying moves water from the material into the air as vapour, and a dehumidifier takes it out of the air. Air movers push dry air across wet surfaces, and the loop repeats until the readings reach a dry standard.

The principle is simple, though it takes care to apply. Wet materials give off vapour, and the rate depends on the humidity of the air next to them. If that air is already damp, drying slows to a crawl. A refrigerant or desiccant dehumidifier lowers the moisture in the air, air movers sweep across surfaces to carry vapour away from them, and the cycle works only if the space is controlled. That is why a restoration crew closes doors and sets up the equipment in a deliberate arrangement and does not simply open the windows.

In a New Hampshire autumn or spring, outdoor air may be cool and damp, and opening windows can bring in more moisture than it lets out. In deep winter the air outside is dry but cold, and the cost is in the heat. Heat helps drying up to a point but cannot do the job alone, and over-heating a wet plaster wall can cause its own cracking. The honest summary is that drying is controlled, and it is measured: the crew records the temperature and humidity of the room and the moisture content of the materials.

Can plaster and lath be saved?

Sometimes. Plaster that is firmly keyed, not sagging and not contaminated can often be dried in place. Plaster that is soft, bulging or soaked with sewage is usually removed.

Plaster is mostly mineral, and clean water does not destroy it the way it destroys paper-faced board. The danger is to the keys, the lumps of plaster that squeeze through the lath and hold the wall on. If they stay firm, the wall can often be dried. Signs of trouble are sagging, bulging, crumbling, a soft feel when pressed and a ceiling that has begun to pull away. A ceiling that is holding water above it, such as after an ice dam, can be dangerous as well as wet, and should not be left until it comes down.

Contamination changes the rule. Plaster that has been in contact with sewage or long-standing water is usually cut out, because the porous face and the lath behind it hold what soaked in. A common approach with clean water is to drill small holes or open a section to let air into the cavity, which means that evidence of the wet area is preserved, and then decide on the basis of readings whether to go further. Cutting everything out by reflex destroys character and cost the owner more. Cutting too little leaves a cavity that grows mold.

What about brick, stone and old basement walls?

Masonry is slow to dry and carries salts and sometimes contaminants. It is dried from both faces where possible, monitored for weeks if needed, and kept ventilated so it does not trap moisture behind finishes.

Manchester's mill district is brick. Walls two or three courses thick absorb water from a flood or a leak and release it gradually. The practical rule is to keep the surface open. Paint, panelling, vinyl or a sealed finish applied too soon can trap moisture, flake and encourage mold. A masonry wall that feels dry to a hand may still read high on a meter set for masonry, and the right reading takes a calibrated instrument and a baseline from a wall known to be dry.

Basements bring groundwater into the picture. The May 2006 flood put dozens of Manchester homes under water as the Merrimack ran about ten feet over flood stage, and a wet cellar in a house near the Piscataquog or low on the river terraces faces the same slow release. Stone foundations dry slowly and are often damp even in a normal year. Dehumidification, grading and gutters matter as much as the drying equipment, because there is no point drying a wall that is wetted again by the next rain.

How are old wood floors dried?

Floors dry from the top, and from below if the cellar or crawl space is open. Boards cup as they dry, and the result is judged after the moisture has equalised, not while it is still moving.

Softwood floors in older houses react quickly to water. They swell, cup and sometimes buckle, but they often flatten again if they dry slowly and evenly. The crew's aim is to avoid forcing it. Specialised mats and low-flow equipment pull moisture through the boards, and a layered floor with a subfloor and a finished floor has a trapped layer between that needs attention. If the space below is accessible, drying from underneath can be quicker and gentler.

Patience pays. Sanding or refinishing before the wood has stabilised can lock in a problem, and a floor that looks flat on a Monday can cup by Friday. Readings over several days are the only reliable guide. If a section has to come up, a trained crew can often lift boards and reinstall them. Old-growth lumber is hard to replace, and a careful lift is worth the extra time. A floor over a cellar that was flooded with sewage is a different story, and the porous boards on top of a contaminated space are judged by the contamination category.

What should happen before demolition in a building from the 1800s?

Ask whether materials have been tested for lead paint and asbestos. Disturbing either can spread them. Asbestos abatement is regulated by the state Department of Environmental Services and lead by the Department of Health and Human Services.

Many Manchester buildings predate the rules that later restricted lead paint and asbestos products. Plaster ceilings, pipe wrap, floor tile and old mastic are all places where such materials can occur, and demolition of a wet ceiling is exactly the kind of work that scatters dust. A careful company asks about the building's age and renovation history, and where the age or the materials suggest a concern it recommends testing before cutting. Sampling is quick compared with the cost of contaminating a home.

This guide names the agencies and asserts nothing about thresholds, since the rules are theirs to state and the sources are conflicting on details. If the answer to the testing question is a shrug, find someone who takes it seriously. For the drying itself, the rule is the same as everywhere. Open as little as the readings justify, protect the rest of the building from dust, and keep a record of what was removed and why.

How do I know when the building is actually dry?

Readings tell you. Materials are measured against a dry standard, usually taken from an unaffected area of the same building. When every wet material reaches it and the humidity is back to normal, drying is done.

Drying ends when the numbers say so, not when the calendar does. A reputable crew takes a reference reading from dry material in the same building, such as an unaffected wall, then measures wet ones each day and shows the trend. The point is to have an objective record. When the readings level out at the reference, the equipment comes out. If they stall, the crew looks for a reason such as hidden water, a source that is still leaking or a space with no air movement.

After the equipment goes, watch for warning signs over the next weeks: a musty smell, staining that returns, paint that blisters, floors that move. These can mean moisture was left in the building. Keep the drying log. It documents the work for an insurer and is useful if a problem appears later. In a house that has stood for a century or more, a thorough job is one that respected how the building was made.

Frequently asked questions

Can I dry a wet plaster wall with a fan and a space heater?

For a small, clean-water spill, ventilation and a dehumidifier can help. Fans and heaters alone often move moisture around without removing it, and a heater can crack plaster. A wall that was soaked, a ceiling that is sagging or any case where the cavity could stay wet needs proper readings and equipment.

How long does drying an older house take?

There is no honest single answer. It depends on the materials, how much water there was, how long it sat and the weather. Masonry and thick plaster take longer than a drywall room. The crew should tell you the plan and update you on the readings.

Will my wood floors be ruined?

Not necessarily. Old softwood boards often recover if they are dried slowly and evenly, though some cupping may remain. Judge the floor after the moisture has settled, not in the first days, and avoid sanding too early.

Why does the crew want to open a wall that looks fine?

Because moisture hides inside the cavity. A small inspection hole lets a camera or meter check the lath, insulation and studs. It is far less destructive than finding mold in the wall months later.

Is it a problem if my building is a brick mill-era block?

It is not a problem, only a different job. Solid brick dries slowly, shared walls and drains connect units, and finishes may contain lead or asbestos. A crew that has worked in such buildings will plan around those points.

Do I need to heat the house to dry it?

Keep the building at a normal indoor temperature in winter, because cold slows drying and a frozen wet pipe can make things worse. Do not crank the thermostat up to compensate for a lack of dehumidification. Controlled humidity is the key.

Sources

  1. U.S. Environmental Protection Agency
  2. New Hampshire Department of Environmental Services
  3. Wikipedia: 2006 New England flood
  4. Wikipedia: Neighborhoods in Manchester, New Hampshire

This guide is general information for Hillsborough County homeowners, not a substitute for an on-site inspection. Prices are estimates. See our disclaimer.

Need help today?

Call any hour and explain what is going on. You get a clear price before any work starts.

Keep reading

More guides

WhatsApp